Specifications of SP32 Series Programmable Logic Controllers
P4A (Integrated 5604 I/O board)
| Controller |
| Processor |
CPU: 32-bit CMOS, 120 MHz clock, integrated watchdog timer |
| Memory |
8 Mb SDRAM, 4 Mb FLASH, 1 Mb CMOS RAM |
| Non-Volatile RAM |
CMOS RAM with lithium battery retains contents for two years with no power |
| I/O |
| Analog Inputs |
Eight, user selectable 0 to 10 V (15-bit) or 0 to 20 mA (14-bit)
One, 0 to 32.678 Vdc (15-bit) |
| Analog Outputs |
Two with optional 5305 analog output module, output range 0 to 20 mA |
| Digital Inputs |
Four on controller board: three digital input/counter, one interrupt with optical isolation |
| Digital Outputs |
One, 30 V/60 mA (used as a status output) |
| Digital I/O (5604 I/O board) |
Thirty two configurable as input or output (1 Amp DC max output/dry
contact input) |
| Communications |
| Serial Port COM1 |
Configurable RS-232 or RS-485, two-wire half duplex or four-wire full/half duplex |
| Serial Ports COM2, COM4 |
RS-232, DTE, eight-pin modular jack, full or half duplex with RTS/CTS control
Implemented Td, Rd, CTS, RTS, DCD, DTR, +5 V |
| Serial Port COM3 |
Located on 5604 I/O module, same specifications as COM2 and COM4 |
| Baud Rates COM1, COM2, COM4 |
300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 |
| Baud Rate COM3 |
1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 |
| Serial Protocols |
Modbus RTU, Modbus ASCII, DNP 3, DF1, PPP |
| Ethernet Port |
RJ45, 10BaseT |
| Network Protocols |
IP: ARP, TCP, TFTP, UDP and ICMP |
| Ethernet Port Protocols |
Modbus TCP, Modbus RTU in UDP, Modbus ASCII in UDP, DNP in TCP,
DNP in UDP |
| Wireless1 |
Spread spectrum radio at 900 MHz2 and 2.4 GHz2 |
| General |
| I/O Terminations |
Six, eight, nine and ten pole, removable terminal blocks, 12 to 22 AWG,
15 A contacts |
| Dimensions |
8.40 in. (213 mm.) wide, 6.13 in. (155 mm.) high, 2.80 in. (72 mm.) deep |
| Packaging |
Corrosion resistant zinc-plated steel with white enamel paint |
| Environment |
5% RH to 95%, non-condensing, -40° to 158°F (-40° to 70°C) |
| Power Input |
11 to 30 Vdc, 4.3 W typical (10.8 W full I/O capacity in use) |
| Warranty |
Three years on parts and labor |
1Available only with optional integrated wireless modules or with stand-alone wireless modules.
2Not applicable in all countries.
P4A (Integrated 5604 I/O board)
| Controller |
| Processor |
CPU: 32-bit CMOS, 120 MHz clock, integrated watchdog timer |
| Memory |
8 Mb SDRAM, 4 Mb FLASH, 1 Mb CMOS RAM |
| Non-Volatile RAM |
CMOS RAM with lithium battery retains contents for two years with no power |
| I/O |
| Analog Inputs |
Eight, user selectable 0 to 5 V (15-bit) or 0 to 20 mA (14-bit) |
| Analog Outputs |
Two with optional 5305 analog output module, output range 0 to 20 mA |
| Digital Inputs |
Four on controller board: three digital input/counter, one interrupt with optical isolation
Sixteen on 5601A I/O module: 6.5 mA typical at 24 V and 3.5 mA typical at 115 V |
| Digital Outputs |
One on controller board: 30 V/60 mA (used as a status output)
Twelve on 5601A I/O module, sealed mechanical relay:
• 0.4 A at 125 Vrms, 2 A at 30 V resistive loads
• 1.0 A at 30 V, 0.2 A at 125 Vrms inductive load with pf=0.4, L/R=7ms
• 250 Vrms, 220 V maximum operating voltage) |
| Communications |
| Serial Port COM1 |
Configurable RS-232 or RS-485, two-wire half duplex or four-wire full/half duplex |
| Serial Ports COM2, COM4 |
RS-232, DTE, eight-pin modular jack, full or half duplex with RTS/CTS control
Implemented Td, Rd, CTS, RTS, DCD, DTR, +5 V |
| Serial Port COM3 |
Located on 5604 I/O module, same specifications as COM2 and COM4 |
| Baud Rates COM1, COM2, COM4 |
300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 |
| Baud Rate COM3 |
1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 |
| Serial Protocols |
Modbus RTU, Modbus ASCII, DNP 3 |
| Ethernet Port |
RJ45, 10BaseT |
| Network Protocols |
IP: ARP, TCP, TFTP, UDP and ICMP |
| Ethernet Port Protocols |
Modbus TCP, Modbus RTU in UDP, Modbus ASCII in UDP |
| Wireless1 |
Spread spectrum radio at 900 MHz2 and 2.4 GHz2 |
| General |
| I/O Terminations |
Six, eight, nine and ten pole, removable terminal blocks, 12 to 22 AWG,
15 A contacts |
| Dimensions |
8.40 in. (213 mm.) wide, 6.13 in. (155 mm.) high, 2.80 in. (72 mm.) deep |
| Packaging |
Corrosion resistant zinc-plated steel with white enamel paint |
| Environment |
5% RH to 95%, non-condensing, -40° to 158°F (-40° to 70°C) |
| Power Input |
11 to 30 Vdc, 3.5 W typical all relays off, 6.5 W typical all relays on |
| Warranty |
Three years on parts and labor |
1Available only with optional integrated wireless modules or with stand-alone wireless modules.
2Not applicable in all countries.
|
 |
